To avoid energy scarcity as well as climate change, a transition towards a sustainable society must be initiated. Within this context, governmental bodies and/or companies often note sustainability as an end goal, for instance as a green circular economy. However, if sustainability cannot be clearly defined as an end goal or measured uniformly and transparently, then the direction and progress towards this goal can only be roughly followed. A clear understanding of and a transparent, uniform measuring technique for sustainability are hence required for sustainable and circular (renewable) energy production pathways (REPPs), as society is asking for an integrated and understandable overview of the decision-making and planning process towards a future sustainable energy system. Therefore, within this dissertation, a new approach is proposed for measuring and optimizing the sustainability of REPPs; it is useful for the analysis, comparison, and optimization of REPP systems on all elements of sustainability. The new approach is applied and tested on a case based on farm-scale, anaerobic digestion (AD), biogas production pathways.
LINK
The increasing demand for Prunus africana resources is an opportunity for its conservation and commercial use to support livelihoods in Africa. The objective for this study was to investigate major steps to advance production of P. africana for long-term commercial use in Uganda. Specific objectives were to explore potential production schemes, setbacks in production and strategies to advance it. The study was done by review of literature, documents and interviews with experts. Results indicated Agroforestry and large plantations to be useful schemes for production. Identified setbacks are: low trade in P. africana, unknown returns from production, competing land uses, long growth period, limited market assurance and information. The lack of a resource assessment for P. africana in forests contributes to its low trade which undermines related economic benefits for national development and incentives to commercial production. We propose that a national Quantitative resource assessment of P. africana in forests is one of the crucial steps that should be undertaken to carefully organise and advance sustainable trade to provide rational incentives for commercial production. Subsequently, production should be localised in suitable sites and producers be organised into cooperatives. Further research to improve returns from commercial production of P. africana is needed.
MULTIFILE
On the Open Research Amsterdam website, the Digital Production Research Group presented its main projects and achievements.--Dutch:Verbinding onderwijs, onderzoek en praktijkIn 2017 is het Robot Lab van de Hogeschool van Amsterdam (HvA) opgericht. Zij transformeren onder andere sloophout tot nieuwe meubels!In deze collectie leest u meer over het Robot Lab en de projecten en die hier worden uitgevoerd.
LINK
The production of denim makes a significant contribution to the environmental impact of the textile industry. The use of mechanically recycled fibers is proven to lower this environmental impact. MUD jeans produce denim using a mixture of virgin and mechanically recycled fibers and has the goal to produce denim with 100% post-consumer textile by 2020. However, denim fabric with 100% mechanically recycled fibers has insufficient mechanical properties. The goal of this project is to investigate the possibilities to increase the content of recycled post-consumer textile fibers in denim products using innovative recycling process technologies.
Recycling of plastics plays an important role to reach a climate neutral industry. To come to a sustainable circular use of materials, it is important that recycled plastics can be used for comparable (or ugraded) applications as their original use. QuinLyte innovated a material that can reach this goal. SmartAgain® is a material that is obtained by recycling of high-barrier multilayer films and which maintains its properties after mechanical recycling. It opens the door for many applications, of which the production of a scoliosis brace is a typical example from the medical field. Scoliosis is a sideways curvature of the spine and wearing an orthopedic brace is the common non-invasive treatment to reduce the likelihood of spinal fusion surgery later. The traditional way to make such brace is inaccurate, messy, time- and money-consuming. Because of its nearly unlimited design freedom, 3D FDM-printing is regarded as the ultimate sustainable technique for producing such brace. From a materials point of view, SmartAgain® has the good fit with the mechanical property requirements of scoliosis braces. However, its fast crystallization rate often plays against the FDM-printing process, for example can cause poor layer-layer adhesion. Only when this problem is solved, a reliable brace which is strong, tough, and light weight could be printed via FDM-printing. Zuyd University of Applied Science has, in close collaboration with Maastricht University, built thorough knowledge on tuning crystallization kinetics with the temperature development during printing, resulting in printed products with improved layer-layer adhesion. Because of this knowledge and experience on developing materials for 3D printing, QuinLyte contacted Zuyd to develop a strategy for printing a wearable scoliosis brace of SmartAgain®. In the future a range of other tailor-made products can be envisioned. Thus, the project is in line with the GoChem-themes: raw materials from recycling, 3D printing and upcycling.
Currently, many novel innovative materials and manufacturing methods are developed in order to help businesses for improving their performance, developing new products, and also implement more sustainability into their current processes. For this purpose, additive manufacturing (AM) technology has been very successful in the fabrication of complex shape products, that cannot be manufactured by conventional approaches, and also using novel high-performance materials with more sustainable aspects. The application of bioplastics and biopolymers is growing fast in the 3D printing industry. Since they are good alternatives to petrochemical products that have negative impacts on environments, therefore, many research studies have been exploring and developing new biopolymers and 3D printing techniques for the fabrication of fully biobased products. In particular, 3D printing of smart biopolymers has attracted much attention due to the specific functionalities of the fabricated products. They have a unique ability to recover their original shape from a significant plastic deformation when a particular stimulus, like temperature, is applied. Therefore, the application of smart biopolymers in the 3D printing process gives an additional dimension (time) to this technology, called four-dimensional (4D) printing, and it highlights the promise for further development of 4D printing in the design and fabrication of smart structures and products. This performance in combination with specific complex designs, such as sandwich structures, allows the production of for example impact-resistant, stress-absorber panels, lightweight products for sporting goods, automotive, or many other applications. In this study, an experimental approach will be applied to fabricate a suitable biopolymer with a shape memory behavior and also investigate the impact of design and operational parameters on the functionality of 4D printed sandwich structures, especially, stress absorption rate and shape recovery behavior.
