At a time when the population is ageing and most people choose to live in their own home for as long as possible, it is important to consider various aspects of supportive and comfortable environments for housing. This study, conducted in South Australia, aims to provide information about the links between the type of housing in which older people live, the weather and occupants’ heating and cooling behaviours as well as their health and well-being. The study used a Computer-Assisted Telephone Interviewing (CATI) system to survey 250 people aged 65 years and over who lived in their own home. The respondents were recruited from three regions representing the three climate zones in South Australia: semi-arid, warm temperate and temperate. The results show that while the majority of respondents reported being in good health, many lived in dwellings with minimal shading and no wall insulation and appeared to rely on the use of heaters and coolers to achieve thermally comfortable conditions. Concerns over the cost of heating and cooling were shared among the majority of respondents and particularly among people with low incomes. Findings from this study highlight the importance of providing information to older people, carers, designers and policy makers about the interrelationships between weather, housing design, heating and cooling behaviours, thermal comfort, energy use and health and well-being, in order to support older people to age in place independently and healthily. https://doi.org/10.1016/j.buildenv.2019.03.023 LinkedIn: https://www.linkedin.com/in/jvhoof1980/
MULTIFILE
Current methods for energy diagnosis in heating, ventilation and air conditioning (HVAC) systems are not consistent with process and instrumentation diagrams (P&IDs) as used by engineers to design and operate these systems, leading to very limited application of energy performance diagnosis in practice. In a previous paper, a generic reference architecture – hereafter referred to as the 4S3F (four symptoms and three faults) framework – was developed. Because it is closely related to the way HVAC experts diagnose problems in HVAC installations, 4S3F largely overcomes the problem of limited application. The present article addresses the fault diagnosis process using automated fault identification (AFI) based on symptoms detected with a diagnostic Bayesian network (DBN). It demonstrates that possible faults can be extracted from P&IDs at different levels and that P&IDs form the basis for setting up effective DBNs. The process was applied to real sensor data for a whole year. In a case study for a thermal energy plant, control faults were successfully isolated using balance, energy performance and operational state symptoms. Correction of the isolated faults led to annual primary energy savings of 25%. An analysis showed that the values of set probabilities in the DBN model are not outcome-sensitive. Link to the formal publication via its DOI https://doi.org/10.1016/j.enbuild.2020.110289
DOCUMENT
Community energy can be conceptualized as a social movement, which aims to develop a sustainable, democratic, and localist energy system. Community energy organizations often take the form of cooperatives and strive for a high level of participation at the neighborhood level. Recently, community energy initiatives took on the challenge to develop neighborhood heating projects, which are citizen-led and sustainable. District heating (DH) projects are characterized by costly investments, a substantial overhaul of local infrastructure, and large installations for heat production. Furthermore, specialized technical knowledge is needed for the design of DH-systems.In the Netherlands, we studied four cases where local energy cooperatives developed such citizen-led neighborhood heating projects. Our primary research question is what constitutes a citizen-led or citizen-supported DH-project? We focus on four themes: first, the internal organization of the CH-project; second its outreach to local citizens; third, the role of technical knowledge and technology choices; fourth, the changing role of municipalities in the local energy transition.We developed a theoretical framework that consists of three main networks: the internal network, constituted by the local energy initiative itself and its surrounding neighborhood; the external network, which is comprised of local and regional governments as well as private companies; and the material network, referring to technological and physical aspects.In the discussion, we situate our findings against a broader European background. We conclude that a democratic structure, transparency of decision making, and a high level of activities to involve the neighborhood are key success factors. Nevertheless, the development of a community DH-project is a time-consuming process that takes a high toll on the participants. We observed that the remunicipalization trend is emerging in the Netherlands. Regarding technology choices, we found that the DH-initiatives became quite knowledgeable on technical issues and stimulated the application of new technologies such as small-scale aquathermal energy. However, in some cases the choice for a low-cost solution led to concessions to the sustainability of the proposed solutions.
DOCUMENT
Lightweight, renewable origin, mild processing, and facile recyclability make thermoplastics the circular construction materials of choice. However, in additive manufacturing (AM), known as 3D printing, mass adoption of thermoplastics lags behind. Upon heating into the melt, particles or filaments fuse first in 2D and successively in 3D, realizing unprecedented geometrical freedom. Despite a scientific understanding of fusion, industrial consortium experts are still confronted with inferior mechanical properties of fused weld interfaces in reality. Exemplary is early mechanical failure in patient-specific and biodegradable medical devices based on Corbion’s poly(lactides), and more technical constructs based on Mitsubishi’s poly(ethylene terephthalate), PET. The origin lies in contradictory low rate of polymer diffusion and entangling, and too high rate of crystallization that is needed to compensate insufficient entangling. Knowing that Zuyd University in close collaboration with Maastricht University has eliminated these contradictory time-scales for PLA-based systems, Corbion and Mitsubishi contacted Zuyd with the question to address and solve their problem. In previous research it has been shown that interfacial co-crystallization of alternating depositioned opposite stereo-specific PLA grades resulted in strengthening of the interface. To promote mass adoption of thermoplastics AM industries, the innovation question has been phrased as follows: What is a technically scalable route to induce toughness in additively manufactured thermoplastics? High mechanical performance translates into an intrinsic brittle to tough transition of stereocomplex reinforced AM products, focusing on fused deposition modeling. Taking the professional request on biocompatibility, engineering performance and scalability into account, the strategies in lowering the yield stress and/or increasing the network strength comprise (i) biobased and biocompatible plasticizers for stereocomplexed poly(lactide), (ii) interfacial co-crystallization of intrinsically tough polyester based materials formulations, and (iii) in-situ interfacial transesterification of recycled PET formulations.
Thermal batteries, which store and release energy by hydrating and dehydrating salt crystals, hold great promise for domestic heating. Such batteries can be charged from waste heat from industrial processes, and discharged to provide neighbourhood heating. Unlike hot water storage systems, the energy is stored at room temperature, so the thermal losses are very low, making a salt battery highly efficient. However, the electrochemical change of the salt due to hydration and dehydration is very small, making it difficult to measure how much energy is stored in a battery. One promising technique is to measure the absolute humidity of the inlet and outlet air flow. The difference in humidity, combined with a rate equation model allows the total mass of water stored in the battery to be calculated, which can then be used to calculate the energy storage and battery power flow. However, there are several uncertainties in this approach. Commercially available sensors age over time, sometimes quite suddenly. It is not yet known if software can be used to compensate for sensor aging, or if a different sensor type is required. In addition to aging, each measurement is subject to random noise, which will be integrated into the model used to calculate the charge of the battery. It is not yet known how the noise will influence charge estimates. On the other hand, the sensor system must be as durable as domestic heating systems (decades). Hence, it is required to understand sensor aging in order to validate the sensor system for its intended use.
In summer 2020, part of a quay wall in Amsterdam collapsed, and in 2010, construction for a parking lot in Amsterdam was hindered by old sewage lines. New sustainable electric systems are being built on top of the foundations of old windmills, in places where industry thrived in the 19th century. All these examples have one point in common: They involve largely unknown and invisible historic underground structures in a densely built historic city. We argue that truly circular building practices in old cities require smart interfaces that allow the circular use of data from the past when planning the future. The continuous use and reuse of the same plots of land stands in stark contrast with the discontinuity and dispersed nature of project-oriented information. Construction and data technology improves, but information about the past is incomplete. We have to break through the lack of historic continuity of data to make building practices truly circular. Future-oriented construction in Amsterdam requires historic knowledge and continuous documentation of interventions and findings over time. A web portal will bring together a range of diverse public and private, professional and citizen stakeholders, each with their own interests and needs. Two creative industry stakeholders, Yume interactive (Yume) and publisher NAI010, come together to work with a major engineering office (Witteveen+Bos), the AMS Institute, the office of Engineering of the Municipality of Amsterdam, UNESCO NL and two faculties of Delft University of Technology (Architecture and Computer Science) to inventorize historic datasets on the Amsterdam underground. The team will connect all the relevant stakeholders to develop a pilot methodology and a web portal connecting historic data sets for use in contemporary and future design. A book publication will document the process and outcomes, highlighting the need for circular practices that tie past, present and future.
