This paper describes the results of a second year Expo project team of Fontys Engineering, department Mechanical Engineering. During this research the design of a configurable damped spring design has been investigated. A calculation tool has been defined and validated using a Nylon 3D printed spring prototype. Also a theoretical design of a stainless steel spring has been made including stress calculations. Finally characterization tests on damping properties have been performed.
DOCUMENT
This study investigates the effect of position on build-plate on the dimensional deviations for stainless steel 316 L samples made by laser powder-bed fusion. To understand the effect of sample position on the build-plate (substrate) with respect to shrinkage and dimensional deviation, 36 samples in a 6 × 6 array were printed with three repetitions. The value of the diameter was measured at 10 points along the vertical axis in the perpendicular and parallel directions to the flow of the assisted gas. The results of the experiment show that there is shrinkage in both directions with respect to the gas flow. However, the extent of deviation in the perpendicular direction to the gas flow is greater compared to the parallel diameters for the samples. This can be related to the pressure of assisted gas and the difference in cooling rate corresponding to the position of the samples on the building substrate. The hypothesis is proved by conducting further experiments regulating the amount of gas flow by adjusting the individual nozzle for the gas flow to the build chamber. The reason for these deviations is speculated to be related to the rheology of the melt pool. This research could lay a solid foundation for the future development of a compensation strategy to nullify the effect of shrinkage and dimensional deviations on parts made using the laser powder-bed fusion technique. The results of shrinkage of the columns appear to suggest that there is an effect on the circularity from the assisting gas.
LINK
This article will discuss philosophical debates on economic growth and environmental sustainability, the role of management responsibility, and the risk of subversion to business as usual. This discussion will be framed using the concepts of Cradle to Cradle (C2C) and Circular Economy about sustainable production. The case study illustrating the danger of subversion of these progressive models discussed here is based on the assignments submitted by Masters students as part of a course related to sustainable production and consumption at Leiden University. The evaluation of the supposedly best practice cases placed on the website of the Ellen MacArthur Foundation or those awarded Cradle to Cradle certificate has led some students to conclude that these cases illustrated green-washing. Larger implications of identified cases of green-washing for the field of sustainable business and ecological management are discussed. “This is a post-peer-review, pre-copyedit version of an article published in 'Philosophy of Management'. The final authenticated version is available online at: https://doi.org/10.1007/s40926-019-00108-x LinkedIn: https://www.linkedin.com/in/helenkopnina/
MULTIFILE
Fouling plays a major role in the Dairy industry. Five criteria: defined flow, no circulation, real factory product, defined product temperature and defined wall temperature, are used to review articles on this topic published between 2003 and 2020. To show the effect of those criteria in experiments, a simulation model is developed. For a good experimental design to measure fouling, the use of a dairy product in a tubular heater with a known developed flow is advised. The temperature-time history of the product and the wall temperature of the heater should be recorded. Circulation of a product will increase the fouling and decrease the flow. Although none of the reviewed articles complied to all criteria, 71% of the reviewed articles met at least two criteria. If not all criteria are met, the results are of less use for the application for process lines on industrial scale. A simulated computer model can be helpful.
DOCUMENT
This report describes the results and recommendations of the assessment of a potential business model for the orchard of Mr. W. Hekkert, Terwolde, focusing on drying fruits for organic muesli.
DOCUMENT
Polycyclic aromatic hydrocarbons (PAHs) are a group of more than hundred compounds that are ubiquitous in our environment. Some of these PAHs are known to be carcinogenic, mutagenic and teratogenic. PAHs have been detected in dried herbs that were cultured in The Netherlands as well as in other European countries above the maximum levels in dried herbs set by the EU (EU, 2015) for benzo(a)pyrene and the sum of the following four PAHs benzo(a)pyrene, benzo[a]anthracene, benzo[b]fluoranteen and chrysene. The origin of these PAHs in herbs is unknown. VNK cultivates, harvests and dries herbs including valerian and would like to identify the source of PAHs to comply to the EU limits for PAHs in herbs. The goal of the present study was to identify the source of PAHs found in valerian root, and to identify possible measures to reduce the concentration of PAHs in valerian root.
DOCUMENT
With this project we strived to contribute to structural reduction of post-harvest food losses and food quality improvement in the Kenyan avocado and dairy value chains through the application of technical solutions and tools as well as improved coordination in those food chains. The consortium had four types of partners: 1. Universities (2 Kenyan, 4 Dutch), 2. Private sector actorsin those chains, 3. Organisations supporting those chains, and 4. Network partners. The applied research has been implemented in cooperation with all partners, whereby students at involved universities conducted most of the field studies and all other consortium partners support and interact depending on the phases.The FORQLAB project targeted two areas in Kenya for both commodities, a relatively well-developed chain in the central highlands and a less-develop chain in Western-Kenya. The research methods were the business to business and multi-stakeholder (living lab) approaches to increase the potential for uptake of successful interventions in the chain. The project consisted of four phases: 1. Inventory and inception, 2. Applied research, 3. Spreading research outputs through living lab networks, 4. Translation of project output in curricula and trainings. The outcomes were: two knowledge exchange platforms (Living Labs) supported with some advice for sustainable food loss reduction, a research agenda, proposals for ICT and other tech solutions and an implementation strategy; communication and teaching materials for universities and TVETs; and knowledge transfer and uptake.
DOCUMENT
Deze publicatie gaat over het lassen van roest- en hittevast staal
DOCUMENT
Legislation in the Netherlands requires routine analysis of drinking water samples for cultivable Legionella species from high-priority installations. A field study was conducted to investigate the presence of Legionella species in thermostatic shower mixer taps. Water samples and the interior of ten thermostatic shower mixer taps were investigated for cultivable Legionella species. In seven cases, Legionella species was found in at least one of the samples. In four cases, Legionella species was detected in the biofilm on the thermostatic shower mixer taps interior, with the highest values on rubber parts, and in five cases in the cold supply water. These results show that thermostatic shower mixer taps can play a role in exceeding the threshold limit for cultivable Legionella species, but the cold supply water can also be responsible. Practical implications: This study showed that contamination of thermostatic shower mixer taps (TSMTs) with Legionella spp. was frequently observed in combination with contamination of the water system. Consequently, a combined focus is necessary to prevent the proliferation of cultivable Legionella spp. in TSMTs. In addition, the results also demonstrated that biofilms on rubbers inside the TSMT had high numbers of Legionella spp., probably because rubber contains relatively high concentrations of biodegradable substrates. Therefore, improvement of the rubber materials is necessary to reduce the proliferation of cultivable Legionella spp. in TSMTs.
DOCUMENT
Dit Tech-Info-blad is tot stand gekomen binnen het kader van het kennisoverdrachtproject "Fabricage van producten met geavanceerde productiemiddelen voor het omvormen en verbinden - FPGP". In dit kader zijn ook de volgende publicaties uitgegeven: TI.07.37 - "Laserlassen van complexe producten" en TI.07.38 - "Geautomatiseerd buigen". Uitgebreide informatie betreffende het laserlassen is tevens te vinden op de websites www.dunneplaat-online.nl en www.verbinden-online.nl, waarop tevens de volgende relevante Tech-Info-bladen vrij gedownload kunnen worden: TI.99.08 - "Laserlassen van beklede plaat", TI.00.11 - "Oppervlaktebehandelingen met de laser (cladden, legeren en dispergeren)", TI.00.12 - "Laser- en waterstraalsnijden van gelamineerde en beklede plaat", TI.07.34 - "Laserlassen vs. conventionele lastechnieken", TI.07.35 - "Omvormen", IOP 7.2 - "Lasertransformatieharden", alsmede de praktijkaanbeveling PA.02.13 - "Oppervlaktebewerkingen met hoogvermogen lasers".
DOCUMENT
